Email: Password: Remember Me | Create Account (Free)

Back to Subject List

Old thread has been locked -- no new posts accepted in this thread
Abhishek Singh
02/04/06 19:15
Read: 1270 times
Bilaspur
India


 
#109215 - Blown Discharge PIN
Responding to: Suresh R's previous message
Suresh R said:

So, i reworked on my circuit to make it error free.
The Timing components are:
1 meg ohm potentiometer and 10uF electrolytic cap (due to present non availability of mylar cap in my nearby, i have used electrolytic as a present option )
Then, i tested with an LED at o/p.
The following things happened:

1) Before trigger - LED is in OFF state

2) When trigger is applied in a state when the 1meg ohm timing potentiometer show zero resistance ( i.e.,before tuning it) - the LED glows constantly and comes to 'OFF' state only when the potentiometer is tuned to some value. else not.


3) Finally, for what ever value i select in the potentiomer(up to 1Meg ohm), the o/p state of the LED after triggering is, just one flicker. The LED is not experiencing any time delay to switch 'OFF'.




but obviously. you should have read data sheet before like every one saying here. PIN 7 is the open collector of the discharge transistor. Even though datasheets says no current limiting is required,i doubt you can connect pin 7 directly to Vcc(when your pot shows zero ohms). Use a Series 1k resistor as Kai suggested. because when ever voltage goes over the threshhold voltage PIN 7 almost shorts to ground.

Whats probably happenning here is when Your pot is shorted to Vcc and you trigger the monostable output goes High momentarily and as PIN 6 is already at VCC it will turn off.

when you increase the resistance letting the capacitor to charge at some rate decided by the R and C voltage AT the pin 6 takes little time to reach threshhold voltage and thats the time you acheive.

finally no time delay is the sign that Steave is right you might have your discharge transitor blown off so that capacitor is always charged and no timedelay. Replace the beast.



Abhishek



List of 57 messages in thread
TopicAuthorDate
Circuit for dispensing unit      Suresh R      01/31/06 05:09      
   1.1 sec monoshot      Abhishek Singh      01/31/06 09:43      
      this thread is apin off from an earlier      Terry Lingle      01/31/06 13:07      
         yes      Steve M. Taylor      01/31/06 13:55      
         timing circuit      Suresh R      02/01/06 04:17      
   Monostable      Andy Neil      01/31/06 12:08      
   Yes.      Steve M. Taylor      01/31/06 13:06      
   Hello All      Suresh R      01/31/06 22:23      
      Description of the "Dispensing Unit"      Andy Neil      02/01/06 00:39      
         using micro      Suresh R      02/02/06 00:25      
            Microcontroller      Andy Neil      02/02/06 01:35      
               Pressure      Steve M. Taylor      02/02/06 03:51      
            What must your circuit can do?      Kai Klaas      02/02/06 07:17      
               0.1 sec      Steve M. Taylor      02/02/06 10:34      
                  but not with a potentiometer      Erik Malund      02/02/06 10:38      
                     Vernier      Steve M. Taylor      02/02/06 13:02      
                        and calibrate it how?      Erik Malund      02/02/06 13:14      
               Precision        Andy Neil      02/02/06 15:13      
                  Sure!      Kai Klaas      02/02/06 16:01      
                     Price      Andy Neil      02/02/06 17:06      
                        Less than 1      Kai Klaas      02/02/06 20:02      
                           levels of precision      Suresh R      02/03/06 05:01      
                              Please have a look into datasheet!      Kai Klaas      02/03/06 05:57      
                                 somewhere here there is a link      Erik Malund      02/03/06 06:51      
                                    Details?      Kai Klaas      02/03/06 07:17      
                                       I recall that in an earlier thread      Erik Malund      02/03/06 07:20      
                              Ooops.      Steve M. Taylor      02/03/06 09:49      
                              Blown Discharge PIN      Abhishek Singh      02/04/06 19:15      
                                 You can also let the smoke out of the      Terry Lingle      02/04/06 22:37      
                                    limits      Steve M. Taylor      02/05/06 06:13      
                                       dissapation      Terry Lingle      02/05/06 09:45      
                                          There must be a point.      Steve M. Taylor      02/05/06 10:31      
                                             Fusing the bonding wires      Terry Lingle      02/05/06 13:59      
                                                History making      Steve M. Taylor      02/05/06 14:47      
                                                Current limiting      Kai Klaas      02/07/06 06:42      
                                 I do go through      Suresh R      02/07/06 01:50      
            schematic and code      Kai Klaas      02/05/06 19:47      
               codes      Suresh R      02/07/06 00:32      
                  Instruction Description      Andy Neil      02/07/06 04:28      
                     not quite      Erik Malund      02/07/06 06:09      
                        Pedantic      Andy Neil      02/07/06 07:12      
                           is that not the pot calling the kettle b      Erik Malund      02/07/06 07:17      
                              Of course not!      Andy Neil      02/07/06 07:31      
                  Answers      Kai Klaas      02/07/06 07:55      
                     Re: codes and shcematic      Suresh R      02/10/06 03:55      
                        Recommendations      Kai Klaas      02/10/06 07:05      
                           Decimal switches - how to start C      Erik Malund      02/10/06 08:09      
      LM555 pin 2 wired wrong.      Charles Bannister      02/01/06 04:45      
         ... and the LED?      Andy Neil      02/01/06 05:31      
            i'm sure thts not the circuit      Abhishek Singh      02/01/06 06:38      
            Astable??      Kai Klaas      02/01/06 11:46      
               I wondered who'd spot that first...      Andy Neil      02/01/06 12:47      
   Damaged?      Kai Klaas      02/01/06 11:51      
      And Andy's correction      Steve M. Taylor      02/01/06 12:03      
         Absolutely!      Kai Klaas      02/01/06 12:24      
   one shot in the foot      Erik Malund      02/01/06 12:31      
      Need not to work unreliably      Kai Klaas      02/02/06 07:10      

Back to Subject List