Email: Password: Remember Me | Create Account (Free)

Back to Subject List

Old thread has been locked -- no new posts accepted in this thread
Suresh R
02/10/06 03:55
Read: 1301 times

#109686 - Re: codes and shcematic
Responding to: Kai Klaas's previous message
Hello Kai,
I went through the codes and the schematic, and iam quite comfortable with it

following which i would like to discuss the following:
Kai Klaas said:

After verification of proper programming, program the lock bits,

I am using a seperate programming device that connects to the computer USB port for programing the micro.
I would like to know how the three lock bits should be programmed.

Kai Klaas said:

You have three BCD switches

I want to use 3 decimal keys(each running from 0-9)to set the value instead of using a BCD switch.
can i know changes need to be done for it.

kai klaas said:

The timer was configured in that way, that timer0 delay plus cycle time of additional instructions yield 10msec.

The additional instructions are all one machine cycle(12 crystal pulses).
There are 10 additional instructions. So the delay will be 120 clk pulses.
But how, the execution time for a particular instruction is calculated?

Also, i would like to know what things need to be studied for writing codes in C or Keil uvision2 (C51 compiler).
what are all the topics i should be knowing.
i.e., will learning the architecture of a particular micro alone will be enough (or)
should i be proficient with the instruction set also, ..e.t.c.,
Is using C language preferred in embeddded software development rather than a Assembly Language? If so - why?
Kindly advice.


List of 57 messages in thread
Circuit for dispensing unit      Suresh R      01/31/06 05:09      
   1.1 sec monoshot      Abhishek Singh      01/31/06 09:43      
      this thread is apin off from an earlier      Terry Lingle      01/31/06 13:07      
         yes      Steve M. Taylor      01/31/06 13:55      
         timing circuit      Suresh R      02/01/06 04:17      
   Monostable      Andy Neil      01/31/06 12:08      
   Yes.      Steve M. Taylor      01/31/06 13:06      
   Hello All      Suresh R      01/31/06 22:23      
      Description of the "Dispensing Unit"      Andy Neil      02/01/06 00:39      
         using micro      Suresh R      02/02/06 00:25      
            Microcontroller      Andy Neil      02/02/06 01:35      
               Pressure      Steve M. Taylor      02/02/06 03:51      
            What must your circuit can do?      Kai Klaas      02/02/06 07:17      
               0.1 sec      Steve M. Taylor      02/02/06 10:34      
                  but not with a potentiometer      Erik Malund      02/02/06 10:38      
                     Vernier      Steve M. Taylor      02/02/06 13:02      
                        and calibrate it how?      Erik Malund      02/02/06 13:14      
               Precision        Andy Neil      02/02/06 15:13      
                  Sure!      Kai Klaas      02/02/06 16:01      
                     Price      Andy Neil      02/02/06 17:06      
                        Less than 1      Kai Klaas      02/02/06 20:02      
                           levels of precision      Suresh R      02/03/06 05:01      
                              Please have a look into datasheet!      Kai Klaas      02/03/06 05:57      
                                 somewhere here there is a link      Erik Malund      02/03/06 06:51      
                                    Details?      Kai Klaas      02/03/06 07:17      
                                       I recall that in an earlier thread      Erik Malund      02/03/06 07:20      
                              Ooops.      Steve M. Taylor      02/03/06 09:49      
                              Blown Discharge PIN      Abhishek Singh      02/04/06 19:15      
                                 You can also let the smoke out of the      Terry Lingle      02/04/06 22:37      
                                    limits      Steve M. Taylor      02/05/06 06:13      
                                       dissapation      Terry Lingle      02/05/06 09:45      
                                          There must be a point.      Steve M. Taylor      02/05/06 10:31      
                                             Fusing the bonding wires      Terry Lingle      02/05/06 13:59      
                                                History making      Steve M. Taylor      02/05/06 14:47      
                                                Current limiting      Kai Klaas      02/07/06 06:42      
                                 I do go through      Suresh R      02/07/06 01:50      
            schematic and code      Kai Klaas      02/05/06 19:47      
               codes      Suresh R      02/07/06 00:32      
                  Instruction Description      Andy Neil      02/07/06 04:28      
                     not quite      Erik Malund      02/07/06 06:09      
                        Pedantic      Andy Neil      02/07/06 07:12      
                           is that not the pot calling the kettle b      Erik Malund      02/07/06 07:17      
                              Of course not!      Andy Neil      02/07/06 07:31      
                  Answers      Kai Klaas      02/07/06 07:55      
                     Re: codes and shcematic      Suresh R      02/10/06 03:55      
                        Recommendations      Kai Klaas      02/10/06 07:05      
                           Decimal switches - how to start C      Erik Malund      02/10/06 08:09      
      LM555 pin 2 wired wrong.      Charles Bannister      02/01/06 04:45      
         ... and the LED?      Andy Neil      02/01/06 05:31      
            i'm sure thts not the circuit      Abhishek Singh      02/01/06 06:38      
            Astable??      Kai Klaas      02/01/06 11:46      
               I wondered who'd spot that first...      Andy Neil      02/01/06 12:47      
   Damaged?      Kai Klaas      02/01/06 11:51      
      And Andy's correction      Steve M. Taylor      02/01/06 12:03      
         Absolutely!      Kai Klaas      02/01/06 12:24      
   one shot in the foot      Erik Malund      02/01/06 12:31      
      Need not to work unreliably      Kai Klaas      02/02/06 07:10      

Back to Subject List