Email: Password: Remember Me | Create Account (Free)

Back to Subject List

Old thread has been locked -- no new posts accepted in this thread
Lynn Reed
03/06/07 11:14
Read: 998 times
Austin
USA


 
#134399 - Some answers
Responding to: Eugene Yong's previous message
1. How does a Pin 3.1 which is also called as TxD differs from other port if i want to use it to transfer a series of bytes data out from the serial port to let's say a modem?

Pin 3.1 is shared between port 3 and the UART TxD. Keep port bit 3.1 = 1 at all times, and it will work.

2. If i am to use ASM to send out a byte of data out from the TxD (P3.1) to a modem.For e.g : i want to send the character "A" to a modem, does the command needed to be sent this looks like this?

MOV SBUF, #A

Close. The command should be
mov sbuf, #'A'
What you did was load sbuf with the address of the accumulator (0e0h)

Can i use the similiar line:

MOV SBUF, #ATD1234567 ?

No, no, no, no.
The move instruction only works on one byte at a time. You will need to put your data in a buffer, and create a loop that will fetch one byte at a time and send it.

4. What would be the appropriate baud value suitable to be configured (TH1) to be used with a modem?

Not enough information. We need your oscillator frequency, and the desired baud rate. And, you are better off using timer 2's baud rate capability.




List of 72 messages in thread
TopicAuthorDate
Serial Communication Related Problem        Eugene Yong      03/06/07 10:49      
   partial answers      Patrick De Groote      03/06/07 11:07      
      Oh yeah, i forgot about that      Eugene Yong      03/06/07 12:09      
   FIRST, THEN, THEN, THEN      Erik Malund      03/06/07 11:10      
      A little bit of sarcasm as usual but often helpful      Eugene Yong      03/06/07 12:25      
         Proper baud rate...      Dave Brooks      03/06/07 12:52      
            baud rate      Erik Malund      03/06/07 13:01      
               calculator      Dave Brooks      03/06/07 13:11      
            modem is autobauding      Jan Waclawek      03/06/07 16:04      
               Noted      Eugene Yong      03/06/07 21:00      
   Some answers      Lynn Reed      03/06/07 11:14      
      Thanks for a patience reply      Eugene Yong      03/06/07 12:33      
   Nothing to add, but ...      Joseph Hebert      03/06/07 11:29      
      i second(ed) that motion      Erik Malund      03/06/07 11:44      
         My location profile?      Eugene Yong      03/06/07 12:38      
            with this known, it would do no good ...      Erik Malund      03/06/07 12:40      
               Radio Shack      Lynn Reed      03/06/07 12:45      
                  Even so      Neil Kurzman      03/06/07 20:44      
                     I can buy it from the local electronic shop      Eugene Yong      03/06/07 20:52      
            Sarcasm      Neil Kurzman      03/06/07 20:52      
               I agree      Eugene Yong      03/06/07 20:57      
      Thanks for understanding and recommendation! - NT      Eugene Yong      03/06/07 12:35      
      More info      Russell Bull      03/06/07 22:28      
         you need to understand the parameters.      Mike Stegmaier      03/07/07 06:28      
            "more valid" evidently means invalid      Erik Malund      03/07/07 07:04      
            not quite      Patrick De Groote      03/07/07 07:29      
               What a wonderful example that when total crap is s      Erik Malund      03/07/07 07:44      
                  lesson      Patrick De Groote      03/07/07 11:43      
            No, it doesn't      Andy Neil      04/03/07 00:37      
   TxD pin to TxD pin?      Eugene Yong      03/07/07 15:31      
      dte-dce-dce-dte      Patrick De Groote      03/07/07 16:00      
         Noted! Thanks!      Eugene Yong      03/07/07 16:20      
            same request question      Jecksons Ben      03/07/07 21:38      
      Meaning of "Transmit"      Andy Neil      04/03/07 04:37      
   same request question 2      Jecksons Ben      03/07/07 21:54      
   Initial command sending code; help me take a look!      Eugene Yong      03/09/07 01:50      
      Make it simple for yourself      Russell Bull      03/09/07 02:50      
         Why the need of circular buffer? Receiving?      Eugene Yong      03/09/07 04:05      
            polling versus interrupt      Patrick De Groote      03/09/07 05:17      
               Check OK string at RXD or DCD at interupt?      Jecksons Ben      03/09/07 21:27      
                  no good      Patrick De Groote      03/10/07 02:14      
                     Voice mode only! No data communication.      Eugene Yong      03/10/07 04:09      
                        you are missing the basics      Patrick De Groote      03/10/07 04:26      
                           NO carrier sent after DCD didn't found      Jecksons Ben      03/11/07 19:54      
                              I do not agree      Patrick De Groote      03/12/07 00:37      
                                 Interupt DCD signal for clear transmission      Jecksons Ben      03/15/07 01:15      
                        For Voice Dialling      Muhammad Fauzan      03/19/07 12:33      
                           and by the way      Muhammad Fauzan      03/19/07 12:36      
                           Sorry for multiposting      Muhammad Fauzan      03/19/07 12:58      
                           The ";" works but...      Eugene Yong      03/22/07 19:46      
                              ";" to return to idle state      Muhammad Fauzan      03/24/07 16:48      
                              +++ with 3 seconds no modem activity      Charles Bannister      03/25/07 03:41      
                                 +++ escape sequence      Andy Neil      03/25/07 07:07      
                                    Monkey See. Monkey Do.      Charles Bannister      03/25/07 08:14      
                                       Now monkey also understand?      Andy Neil      03/26/07 00:26      
                                 Are you mistaken?      Eugene Yong      03/25/07 23:36      
                                    I think so      Andy Neil      03/26/07 00:24      
            Circular buffers      Russell Bull      03/23/07 00:42      
               Initial code for receiving modem response      Eugene Yong      03/26/07 10:38      
                  don't fiddle with the timer, let it run      Erik Malund      03/26/07 10:43      
                     Understood, will run TR1 in global init, thx! - NT      Eugene Yong      03/26/07 10:48      
                  check this out, Eugene...      Dave Brooks      03/26/07 10:52      
                     Ah! Didn't know that! Thanks! -NT      Eugene Yong      03/26/07 11:09      
                     Code; modem commands & responses      Andy Neil      03/26/07 11:23      
   V.250 (formerly V.25-ter) - get it free!      Andy Neil      03/26/07 14:28      
   code,modem command and response      Jecksons Ben      04/01/07 20:20      
   system froze when connected to hyperterminal      Eugene Yong      04/02/07 13:39      
      Your code...      Russell Bull      04/02/07 23:48      
         It should not be a hardware problem since..      Eugene Yong      04/03/07 01:43      
            Not necessarily      Andy Neil      04/03/07 02:42      
      Just taking a stab at it...      Chris Singer      04/03/07 10:22      
         two 'ugly' guesses      Erik Malund      04/03/07 10:44      

Back to Subject List