Email: Password: Remember Me | Create Account (Free)

Back to Subject List

Old thread has been locked -- no new posts accepted in this thread
Eugene Yong
03/10/07 04:09
Read: 1026 times
Malacca
Malaysia


 
#134680 - Voice mode only! No data communication.
Responding to: Patrick De Groote's previous message
In my case, i only need the modem to dial to a receiver, then detect if the call is answered. once the call is answered, the modem will output a series of DTMF tones at various timing (simulate a sound of alarm perhaps). I don't think DCD is necessary here, is there? RxD and TxD would be sufficient for most of the basic things i wanted to do.

Also, a question about hyperterminal, i have tried communicating with the modem, and upon sending ATDT######### where ####### is my cell phone number, it successfully dialed the number and i answered it. However upon answering the call, any further attempt to communicate with the modem through the hyperterminal will result in a "NO CARRIER" error and disconnection. I have read the AT Command manual over and over again but i can't seems to find a solution to it. What i need to perform is that, upon answering call, i want to be able to transmit any DTMF tones over the connection so that the receiver can hear it. No voice transmission is necessary. What am i missing?

List of 72 messages in thread
TopicAuthorDate
Serial Communication Related Problem        Eugene Yong      03/06/07 10:49      
   partial answers      Patrick De Groote      03/06/07 11:07      
      Oh yeah, i forgot about that      Eugene Yong      03/06/07 12:09      
   FIRST, THEN, THEN, THEN      Erik Malund      03/06/07 11:10      
      A little bit of sarcasm as usual but often helpful      Eugene Yong      03/06/07 12:25      
         Proper baud rate...      Dave Brooks      03/06/07 12:52      
            baud rate      Erik Malund      03/06/07 13:01      
               calculator      Dave Brooks      03/06/07 13:11      
            modem is autobauding      Jan Waclawek      03/06/07 16:04      
               Noted      Eugene Yong      03/06/07 21:00      
   Some answers      Lynn Reed      03/06/07 11:14      
      Thanks for a patience reply      Eugene Yong      03/06/07 12:33      
   Nothing to add, but ...      Joseph Hebert      03/06/07 11:29      
      i second(ed) that motion      Erik Malund      03/06/07 11:44      
         My location profile?      Eugene Yong      03/06/07 12:38      
            with this known, it would do no good ...      Erik Malund      03/06/07 12:40      
               Radio Shack      Lynn Reed      03/06/07 12:45      
                  Even so      Neil Kurzman      03/06/07 20:44      
                     I can buy it from the local electronic shop      Eugene Yong      03/06/07 20:52      
            Sarcasm      Neil Kurzman      03/06/07 20:52      
               I agree      Eugene Yong      03/06/07 20:57      
      Thanks for understanding and recommendation! - NT      Eugene Yong      03/06/07 12:35      
      More info      Russell Bull      03/06/07 22:28      
         you need to understand the parameters.      Mike Stegmaier      03/07/07 06:28      
            "more valid" evidently means invalid      Erik Malund      03/07/07 07:04      
            not quite      Patrick De Groote      03/07/07 07:29      
               What a wonderful example that when total crap is s      Erik Malund      03/07/07 07:44      
                  lesson      Patrick De Groote      03/07/07 11:43      
            No, it doesn't      Andy Neil      04/03/07 00:37      
   TxD pin to TxD pin?      Eugene Yong      03/07/07 15:31      
      dte-dce-dce-dte      Patrick De Groote      03/07/07 16:00      
         Noted! Thanks!      Eugene Yong      03/07/07 16:20      
            same request question      Jecksons Ben      03/07/07 21:38      
      Meaning of "Transmit"      Andy Neil      04/03/07 04:37      
   same request question 2      Jecksons Ben      03/07/07 21:54      
   Initial command sending code; help me take a look!      Eugene Yong      03/09/07 01:50      
      Make it simple for yourself      Russell Bull      03/09/07 02:50      
         Why the need of circular buffer? Receiving?      Eugene Yong      03/09/07 04:05      
            polling versus interrupt      Patrick De Groote      03/09/07 05:17      
               Check OK string at RXD or DCD at interupt?      Jecksons Ben      03/09/07 21:27      
                  no good      Patrick De Groote      03/10/07 02:14      
                     Voice mode only! No data communication.      Eugene Yong      03/10/07 04:09      
                        you are missing the basics      Patrick De Groote      03/10/07 04:26      
                           NO carrier sent after DCD didn't found      Jecksons Ben      03/11/07 19:54      
                              I do not agree      Patrick De Groote      03/12/07 00:37      
                                 Interupt DCD signal for clear transmission      Jecksons Ben      03/15/07 01:15      
                        For Voice Dialling      Muhammad Fauzan      03/19/07 12:33      
                           and by the way      Muhammad Fauzan      03/19/07 12:36      
                           Sorry for multiposting      Muhammad Fauzan      03/19/07 12:58      
                           The ";" works but...      Eugene Yong      03/22/07 19:46      
                              ";" to return to idle state      Muhammad Fauzan      03/24/07 16:48      
                              +++ with 3 seconds no modem activity      Charles Bannister      03/25/07 03:41      
                                 +++ escape sequence      Andy Neil      03/25/07 07:07      
                                    Monkey See. Monkey Do.      Charles Bannister      03/25/07 08:14      
                                       Now monkey also understand?      Andy Neil      03/26/07 00:26      
                                 Are you mistaken?      Eugene Yong      03/25/07 23:36      
                                    I think so      Andy Neil      03/26/07 00:24      
            Circular buffers      Russell Bull      03/23/07 00:42      
               Initial code for receiving modem response      Eugene Yong      03/26/07 10:38      
                  don't fiddle with the timer, let it run      Erik Malund      03/26/07 10:43      
                     Understood, will run TR1 in global init, thx! - NT      Eugene Yong      03/26/07 10:48      
                  check this out, Eugene...      Dave Brooks      03/26/07 10:52      
                     Ah! Didn't know that! Thanks! -NT      Eugene Yong      03/26/07 11:09      
                     Code; modem commands & responses      Andy Neil      03/26/07 11:23      
   V.250 (formerly V.25-ter) - get it free!      Andy Neil      03/26/07 14:28      
   code,modem command and response      Jecksons Ben      04/01/07 20:20      
   system froze when connected to hyperterminal      Eugene Yong      04/02/07 13:39      
      Your code...      Russell Bull      04/02/07 23:48      
         It should not be a hardware problem since..      Eugene Yong      04/03/07 01:43      
            Not necessarily      Andy Neil      04/03/07 02:42      
      Just taking a stab at it...      Chris Singer      04/03/07 10:22      
         two 'ugly' guesses      Erik Malund      04/03/07 10:44      

Back to Subject List