Email: Password: Remember Me | Create Account (Free)

Back to Subject List

Old thread has been locked -- no new posts accepted in this thread
Erik Malund
10/31/11 07:04
Read: 510 times
Mt Airy, Nc
USA


 
#184479 - you will be lucky to get 16 bits
Responding to: Zeeshan Ashraf's previous message
So now if i select the cells, i would atleast consider a safety factor of 1.25 for sizing the load cells. So if :

Total desired material weight = ~950 KGs
Dead weight of hopper = 250 KGs,
then total weight = 1200 KGs
Applying safety factor of 1.25 = 1200 * 1.25 = 1500 KGs
For 3x load-cells, each load cell capacity = 1500 / 3 = 500 KGs

waaay too low a safety factor, it is possible that (possibly only with one material) most/all the material will be dumped in one corner. I would rate all 4 full weight

As for the resolution, there is no doubt that 'Legal for Trade' lists resolutions to be 3000 ~ 6000 counts tops.
since when is 'Legal for Trade' a matter of resolution?? it is a matter of precision do not confuse the two

A 24-bit ADC, with Digital filters applied, would actually result in around 18 bits of useable resolution. But again, this is only ADC resolution. The rest of the Analog system should be able to deliver this 18 bits of resolution too.
no, you will get 24 bits of resolution, but you will be lucky to get 16 bits of precision unless your budget is HUGE.

also I have heard nothing about auto-zero

Erik

List of 58 messages in thread
TopicAuthorDate
Load-cell conditioning / summing      Zeeshan Ashraf      10/29/11 10:29      
   what is that?      Erik Malund      10/29/11 15:43      
      RE: #184430 - what is that?      Zeeshan Ashraf      10/29/11 15:45      
         then say what you mean      Erik Malund      10/29/11 15:53      
            your description leaves something unclear      Erik Malund      10/29/11 16:02      
               RE: #184435 - your description leaves something unclear      Zeeshan Ashraf      10/29/11 16:27      
                  where are the loadcells???      Erik Malund      10/30/11 06:08      
                     RE:      Zeeshan Ashraf      10/30/11 09:01      
      RE: #184430 - what is that?      Zeeshan Ashraf      10/29/11 15:56      
         some Q/A      Stefan KAnev      10/30/11 14:14      
            RE      Zeeshan Ashraf      10/30/11 15:27      
               Q/A 2      Stefan KAnev      10/31/11 03:00      
                  RE      Zeeshan Ashraf      10/31/11 04:18      
                     re re      Stefan KAnev      10/31/11 05:00      
                     get rid of that summing amp      Erik Malund      10/31/11 07:09      
               you will be lucky to get 16 bits      Erik Malund      10/31/11 07:04      
                  Precision again...      Kai Klaas      10/31/11 16:58      
                     Comparison      Per Westermark      11/01/11 01:12      
                     RE      Zeeshan Ashraf      11/01/11 02:20      
                        why do you keep babbling about a summing amp      Erik Malund      11/01/11 06:41      
                        Priorities...        Kai Klaas      11/01/11 07:07      
                           RE      Zeeshan Ashraf      11/01/11 07:45      
                              cirrus, ti      Stefan KAnev      11/01/11 08:42      
                                 maxim, linear tech, Analog Devices      Erik Malund      11/01/11 10:09      
                                 RE      Zeeshan Ashraf      11/01/11 17:36      
                              it takes the same time ...      Erik Malund      11/01/11 10:14      
               500 running foot of cable      Stefan KAnev      11/01/11 22:25      
                  RE      Zeeshan Ashraf      11/01/11 22:57      
                     Go for ADC with multiplexed inputs instead of multiple ADC        Per Westermark      11/02/11 07:14      
                        Good Advice      Michael Karas      11/02/11 08:00      
                           It depends...      Kai Klaas      11/02/11 08:48      
                              This is a MODULAR concept !      Zeeshan Ashraf      11/02/11 19:57      
                                 it depends      Stefan KAnev      11/03/11 00:50      
                                 don't be ridiculous      Erik Malund      11/03/11 07:17      
                                    Consider other parameters too.      Zeeshan Ashraf      11/03/11 08:16      
                                       calibration      Stefan KAnev      11/03/11 08:46      
                                       if you do not buy bootleg parts ...      Erik Malund      11/03/11 08:50      
                                          Voltage reference      Per Westermark      11/03/11 09:08      
            Accuracy...      Kai Klaas      10/30/11 16:40      
               RE      Zeeshan Ashraf      10/30/11 16:55      
                  Keep the signal paths as simple as possible.      Michael Karas      10/30/11 20:34      
                  sun umbrella      Stefan KAnev      10/31/11 03:10      
   Separate Gain Paths - Not The Best      Michael Karas      10/29/11 23:33      
      RE: #184439 - Separate Gain Paths - Not The Best      Zeeshan Ashraf      10/30/11 00:11      
         Error Budget Calculations?      Michael Karas      10/30/11 09:50      
            Hysteresis      Kai Klaas      10/30/11 10:14      
         This should alarm you!      Kai Klaas      10/30/11 09:58      
            RE      Zeeshan Ashraf      10/30/11 10:14      
               No contradiction...      Kai Klaas      10/30/11 10:22      
                  RE      Zeeshan Ashraf      10/30/11 10:40      
                     Digital Summing        Michael Karas      10/30/11 12:55      
               with DC exitacion ...      Erik Malund      10/31/11 07:20      
            welcome on board      Erik Malund      10/31/11 07:14      
      RE:      Zeeshan Ashraf      10/30/11 00:16      
   Look at ADuC845      Oliver Sedlacek      10/31/11 01:44      
      ADuC845      Russell Bull      11/16/11 20:54      
         Noise V good      Oliver Sedlacek      11/17/11 04:39      
            Ok, then      Erik Malund      11/17/11 06:26      

Back to Subject List