Email: Password: Remember Me | Create Account (Free)

Back to Subject List

Old thread has been locked -- no new posts accepted in this thread
Per Westermark
11/01/11 01:12
Read: 481 times
Sweden


 
#184498 - Comparison
Responding to: Kai Klaas's previous message
It is hard to measure weight in comparison to just measuring DC voltages.

So why are even quite expensive multimeters unable to measure voltages with really high precision (note precision - not resolution)? The multimeter can basically feed the voltage directly to the ADC, without any temperature-drifting sensor involved. It "only" need to care about the noise picked up in wires, and the quality of the voltage reference. And there are lots of reasonably priced ADC with very, good linearity.

When comparing with a multimeter - notice what happens when switching from DC mode to measuring AC, resistance, capacitance, temperature, ... The precision tends to drop because more electronics and sensors gets involved.

List of 58 messages in thread
TopicAuthorDate
Load-cell conditioning / summing      Zeeshan Ashraf      10/29/11 10:29      
   what is that?      Erik Malund      10/29/11 15:43      
      RE: #184430 - what is that?      Zeeshan Ashraf      10/29/11 15:45      
         then say what you mean      Erik Malund      10/29/11 15:53      
            your description leaves something unclear      Erik Malund      10/29/11 16:02      
               RE: #184435 - your description leaves something unclear      Zeeshan Ashraf      10/29/11 16:27      
                  where are the loadcells???      Erik Malund      10/30/11 06:08      
                     RE:      Zeeshan Ashraf      10/30/11 09:01      
      RE: #184430 - what is that?      Zeeshan Ashraf      10/29/11 15:56      
         some Q/A      Stefan KAnev      10/30/11 14:14      
            RE      Zeeshan Ashraf      10/30/11 15:27      
               Q/A 2      Stefan KAnev      10/31/11 03:00      
                  RE      Zeeshan Ashraf      10/31/11 04:18      
                     re re      Stefan KAnev      10/31/11 05:00      
                     get rid of that summing amp      Erik Malund      10/31/11 07:09      
               you will be lucky to get 16 bits      Erik Malund      10/31/11 07:04      
                  Precision again...      Kai Klaas      10/31/11 16:58      
                     Comparison      Per Westermark      11/01/11 01:12      
                     RE      Zeeshan Ashraf      11/01/11 02:20      
                        why do you keep babbling about a summing amp      Erik Malund      11/01/11 06:41      
                        Priorities...        Kai Klaas      11/01/11 07:07      
                           RE      Zeeshan Ashraf      11/01/11 07:45      
                              cirrus, ti      Stefan KAnev      11/01/11 08:42      
                                 maxim, linear tech, Analog Devices      Erik Malund      11/01/11 10:09      
                                 RE      Zeeshan Ashraf      11/01/11 17:36      
                              it takes the same time ...      Erik Malund      11/01/11 10:14      
               500 running foot of cable      Stefan KAnev      11/01/11 22:25      
                  RE      Zeeshan Ashraf      11/01/11 22:57      
                     Go for ADC with multiplexed inputs instead of multiple ADC        Per Westermark      11/02/11 07:14      
                        Good Advice      Michael Karas      11/02/11 08:00      
                           It depends...      Kai Klaas      11/02/11 08:48      
                              This is a MODULAR concept !      Zeeshan Ashraf      11/02/11 19:57      
                                 it depends      Stefan KAnev      11/03/11 00:50      
                                 don't be ridiculous      Erik Malund      11/03/11 07:17      
                                    Consider other parameters too.      Zeeshan Ashraf      11/03/11 08:16      
                                       calibration      Stefan KAnev      11/03/11 08:46      
                                       if you do not buy bootleg parts ...      Erik Malund      11/03/11 08:50      
                                          Voltage reference      Per Westermark      11/03/11 09:08      
            Accuracy...      Kai Klaas      10/30/11 16:40      
               RE      Zeeshan Ashraf      10/30/11 16:55      
                  Keep the signal paths as simple as possible.      Michael Karas      10/30/11 20:34      
                  sun umbrella      Stefan KAnev      10/31/11 03:10      
   Separate Gain Paths - Not The Best      Michael Karas      10/29/11 23:33      
      RE: #184439 - Separate Gain Paths - Not The Best      Zeeshan Ashraf      10/30/11 00:11      
         Error Budget Calculations?      Michael Karas      10/30/11 09:50      
            Hysteresis      Kai Klaas      10/30/11 10:14      
         This should alarm you!      Kai Klaas      10/30/11 09:58      
            RE      Zeeshan Ashraf      10/30/11 10:14      
               No contradiction...      Kai Klaas      10/30/11 10:22      
                  RE      Zeeshan Ashraf      10/30/11 10:40      
                     Digital Summing        Michael Karas      10/30/11 12:55      
               with DC exitacion ...      Erik Malund      10/31/11 07:20      
            welcome on board      Erik Malund      10/31/11 07:14      
      RE:      Zeeshan Ashraf      10/30/11 00:16      
   Look at ADuC845      Oliver Sedlacek      10/31/11 01:44      
      ADuC845      Russell Bull      11/16/11 20:54      
         Noise V good      Oliver Sedlacek      11/17/11 04:39      
            Ok, then      Erik Malund      11/17/11 06:26      

Back to Subject List