Email: Password: Remember Me | Create Account (Free)

Back to Subject List

Old thread has been locked -- no new posts accepted in this thread
Jim Granville
02/21/12 12:42
Read: 1069 times


 
Msg Score: +1
 +1 Good Answer/Helpful
#186115 - and even more questions for your tutor
Responding to: Michael Karas's previous message
above specs are good, but I would add does it need to be 10.000x ?
ie ask what short term, and long term deviation are allowed.

The simplest 8051 method of doing this, will be to capture a full cycle of Fi, and then divide that time by 20, and load into a Toggle-Pin timer.
Choose an 8051 variant with prescaled timers, and you can cascade some timers
to capture to 32 bits,
That will be close to 10x, and it you want a precise average, you would add code that calculated the two closest toggle pin values, one above 10x and one below.
You then continually count the 10x edges, and swap between the reload values, to give a long term average of 10.00.
Run a paced update, so the output always generates 10 cycles per IP reading.
This is less computation than DDS, and more precise long term.

List of 52 messages in thread
TopicAuthorDate
frequency multiplier x 10      Mahmood Elnasser      02/20/12 14:29      
   You need some specs first.      Michael Karas      02/20/12 19:56      
      and even more questions for your tutor        Jim Granville      02/21/12 12:42      
   Analog solution...      Kai Klaas      02/21/12 05:49      
      Input wave form      Per Westermark      02/21/12 06:09      
      Too Bad...      Michael Karas      02/21/12 06:16      
   have you considered a "rate multiplier"?      Richard Erlacher      02/21/12 08:18      
   PCA?      Erik Malund      02/21/12 12:51      
      PCA Yes      Michael Karas      02/21/12 15:38      
   Update      Mahmood Elnasser      02/22/12 00:43      
      2 i.c.s plus 6 R, C      David Prentice      02/22/12 03:03      
      4046 / 7490      Michael Karas      02/22/12 03:36      
      I put my bet in the digital solution      Daniel Contarino      02/22/12 13:33      
         digital solution      Mahmood Elnasser      02/22/12 13:46      
            MCU / CPLD      Michael Karas      02/22/12 13:57      
            Simple digital solution...      Kai Klaas      02/23/12 05:59      
               Engine too fast      Mahmood Elnasser      02/23/12 06:48      
                  it could be made simpler        Jim Granville      02/29/12 19:22      
                     cute      Erik Malund      03/01/12 08:07      
               OR      Erik Malund      02/23/12 06:52      
   Frequency Multipiler      Satish S Munot      02/29/12 10:06      
      Motivation?      Per Westermark      02/29/12 10:14      
         Motivation ?????????      Satish S Munot      02/29/12 10:55      
            Motives      Per Westermark      02/29/12 11:24      
               OK      Satish S Munot      02/29/12 12:40      
                  motivation guess      Maarten Brock      03/02/12 01:14      
                     I had the same feeling...      Kai Klaas      03/02/12 08:25      
                        and if you looked at any of his previous posts ...      Richard Erlacher      03/02/12 20:02      
   A number of thins concern me ...      Richard Erlacher      02/29/12 12:31      
      answers      Mahmood Elnasser      02/29/12 14:45      
      Boring...      Kai Klaas      02/29/12 16:05      
         And in this case...      Daniel Contarino      02/29/12 18:11      
            Yes ... but ...      Richard Erlacher      02/29/12 20:12      
               Making what you need, from what you can get..      Jim Granville      02/29/12 22:14      
                  slogans      Satish S Munot      02/29/12 23:59      
                  Is that what the display needs?      Richard Erlacher      03/01/12 06:38      
                     10-700 Hz is expected output frequency - not input frequency      Per Westermark      03/01/12 06:57      
                        I did make one mistake      Richard Erlacher      03/01/12 07:18      
                           old rpm analog (or digital) display is what they have      Jim Granville      03/01/12 12:01      
                              bursts...      Kai Klaas      03/01/12 13:19      
                                 See LM2917 for ancient tacho examples      Jim Granville      03/01/12 13:40      
   PLL      Mahmood Elnasser      03/18/12 06:57      
   More detail?      Richard Erlacher      03/18/12 12:30      
      Yes, more details, please...      Kai Klaas      03/18/12 12:43      
         Details      Mahmood Elnasser      03/31/12 00:24      
            This can have to do ...      Kai Klaas      03/31/12 09:25      
               sharp edges      Mahmood Elnasser      04/01/12 03:59      
                  Which phase-detector?      Richard Erlacher      04/01/12 08:21      
               re: this can have      Andy Peters      04/02/12 10:49      
                  What I would do...        Kai Klaas      04/03/12 07:40      
                     Very Low Frequency      Mahmood Elnasser      04/19/12 15:30      
                        Give it a try...      Kai Klaas      04/19/12 17:14      

Back to Subject List