Email: Password: Remember Me | Create Account (Free)

Back to Subject List

Old thread has been locked -- no new posts accepted in this thread
Erik Malund
11/30/12 15:11
Read: 961 times
Mt Airy, Nc
USA


 
#188930 - another solution
Responding to: Daniel Contarino's previous message
When touching pin 6 (XTAL1, input, high impedance) the clock stops. But, sometimes, with everything connected to ground (even my body), the program stops and it does not start even after recycling power! It is necessary to reprogram the part.
Solution: cover the Xtal and pin6 area with plastic weldind rod.

another solution: don't touch pin 6. Why would anyone want to do that

It seems that the flash got corrupted by some high voltage spike
not a surprise. If you want to be able to do a touchy feely you need to make sure the decoupling is perfect and that ther are no high impedance entries to the chip such as an unconnected input. (neighbor pin to what you touch)

Erik

List of 33 messages in thread
TopicAuthorDate
C8051F231 experiences      Daniel Contarino      11/30/12 14:43      
   another solution      Erik Malund      11/30/12 15:11      
   The probabilities are low...      Daniel Contarino      11/30/12 18:34      
      think about what happens when you add a finger      Richard Erlacher      11/30/12 22:55      
         The point is ...      Daniel Contarino      12/01/12 03:08      
            Yes ... the underlying issue is the flash ...       Richard Erlacher      12/01/12 11:28      
               Out of my office, but...      Daniel Contarino      12/01/12 14:05      
                  Don't think in Vcc, ESD or hum...      Daniel Contarino      12/02/12 09:24      
   Apparently several C8051F2xx parts have the same pinout      Richard Erlacher      12/01/12 14:25      
   Characteristic for in system programmable flash micros...      Kai Klaas      12/01/12 18:25      
      All too true ... sadly ...       Richard Erlacher      12/01/12 20:13      
         Power-on slope rate...      Kai Klaas      12/02/12 05:31      
            Sorry, my post should be here, no up there...      Daniel Contarino      12/02/12 09:58      
            Have you any basis for that rate?      Richard Erlacher      12/02/12 10:15      
               Vdd ramp time      Maarten Brock      12/03/12 06:15      
               Some datasheets show numbers...      Kai Klaas      12/03/12 07:05      
                  Those aren't the "usual" 805x-core MCU's      Richard Erlacher      12/03/12 17:43      
                     There aren't many "usual" 8051-cores anymore...      Kai Klaas      12/03/12 18:13      
                        How dangerous power ups can be...      Kai Klaas      12/04/12 06:20      
                           I believe it      Richard Erlacher      12/04/12 08:59      
                              (dV/dt) examples      Jim Granville      12/04/12 13:14      
                                 They don't know it either...      Kai Klaas      12/04/12 18:49      
                                    dV/dT etc       Jim Granville      12/04/12 21:39      
                                       reset request...      Kai Klaas      12/05/12 06:21      
                                          That's what disturbs me greatly      Richard Erlacher      12/06/12 00:19      
                                             It IS disturbing!      Kai Klaas      12/06/12 08:02      
                                                Where this began ... at least for me ...       Richard Erlacher      12/06/12 09:43      
                                                   So, you took the hard road...      Kai Klaas      12/06/12 10:41      
                                                      We've all had that experience       Richard Erlacher      12/06/12 16:23      
   probable cause      Brent Wilson      02/04/13 20:32      
      Brent, this is very nice      Erik Malund      02/05/13 06:38      
         forum no longer down      Maarten Brock      02/05/13 07:33      
      Thank you!      Daniel Contarino      02/05/13 15:04      

Back to Subject List