Email: Password: Remember Me | Create Account (Free)

Back to Subject List

Old thread has been locked -- no new posts accepted in this thread
Jim Granville
12/04/12 21:39
Read: 900 times


 
#188966 - dV/dT etc
Responding to: Kai Klaas's previous message
Kai Klaas said:
......
During a power down, on the other hand, Vcc must fall sufficiently slowly so that the BOR can trip a reset. After each power down Vcc must fall down to 0V.


I know designers in the Alarm sector, who often use power-removal-watchdogs, as this catches everything.
It will recover from a latch-up, and any pgm crash that fell between two stools of POR and BOD.
Quite a few parts have pins called RESET that are more correctly 'reset request' pins.


List of 33 messages in thread
TopicAuthorDate
C8051F231 experiences      Daniel Contarino      11/30/12 14:43      
   another solution      Erik Malund      11/30/12 15:11      
   The probabilities are low...      Daniel Contarino      11/30/12 18:34      
      think about what happens when you add a finger      Richard Erlacher      11/30/12 22:55      
         The point is ...      Daniel Contarino      12/01/12 03:08      
            Yes ... the underlying issue is the flash ...       Richard Erlacher      12/01/12 11:28      
               Out of my office, but...      Daniel Contarino      12/01/12 14:05      
                  Don't think in Vcc, ESD or hum...      Daniel Contarino      12/02/12 09:24      
   Apparently several C8051F2xx parts have the same pinout      Richard Erlacher      12/01/12 14:25      
   Characteristic for in system programmable flash micros...      Kai Klaas      12/01/12 18:25      
      All too true ... sadly ...       Richard Erlacher      12/01/12 20:13      
         Power-on slope rate...      Kai Klaas      12/02/12 05:31      
            Sorry, my post should be here, no up there...      Daniel Contarino      12/02/12 09:58      
            Have you any basis for that rate?      Richard Erlacher      12/02/12 10:15      
               Vdd ramp time      Maarten Brock      12/03/12 06:15      
               Some datasheets show numbers...      Kai Klaas      12/03/12 07:05      
                  Those aren't the "usual" 805x-core MCU's      Richard Erlacher      12/03/12 17:43      
                     There aren't many "usual" 8051-cores anymore...      Kai Klaas      12/03/12 18:13      
                        How dangerous power ups can be...      Kai Klaas      12/04/12 06:20      
                           I believe it      Richard Erlacher      12/04/12 08:59      
                              (dV/dt) examples      Jim Granville      12/04/12 13:14      
                                 They don't know it either...      Kai Klaas      12/04/12 18:49      
                                    dV/dT etc       Jim Granville      12/04/12 21:39      
                                       reset request...      Kai Klaas      12/05/12 06:21      
                                          That's what disturbs me greatly      Richard Erlacher      12/06/12 00:19      
                                             It IS disturbing!      Kai Klaas      12/06/12 08:02      
                                                Where this began ... at least for me ...       Richard Erlacher      12/06/12 09:43      
                                                   So, you took the hard road...      Kai Klaas      12/06/12 10:41      
                                                      We've all had that experience       Richard Erlacher      12/06/12 16:23      
   probable cause      Brent Wilson      02/04/13 20:32      
      Brent, this is very nice      Erik Malund      02/05/13 06:38      
         forum no longer down      Maarten Brock      02/05/13 07:33      
      Thank you!      Daniel Contarino      02/05/13 15:04      

Back to Subject List