Email: Password: Remember Me | Create Account (Free)

Back to Subject List

Old thread has been locked -- no new posts accepted in this thread
Per Westermark
02/15/12 04:47
Read: 540 times
Sweden


 
#185980 - IAP don't mean boot loader exists
Responding to: Jecksons Ben's previous message
IAP is In Application Programming - i.e. that your application have means to modify the flash contents. So your application may use whatever interface the processor have to receive new program content. Be it UART, CAN, I2C, SPI, Ethernet, USB, SD-card, ...

And ISP - In System Programming - just means that you can program a chip without disconnecting it from the board. But that might be done using a UART. Or I2C. Or SPI. Or something else. It probably means that there is a boot loader in there somewhere, but the chip could instead manage by the use of JTAG or similar.

List of 42 messages in thread
TopicAuthorDate
89LP52      Rick Gebhardt      02/12/12 23:58      
   Drop In Replacement??      Michael Karas      02/13/12 00:15      
   Always give full part numbers!      Andy Neil      02/13/12 00:52      
      STK500, AVRStudio et al.      Jan Waclawek      02/13/12 01:55      
         Officially recommended      Per Westermark      02/13/12 02:51      
      AT89LP Developer Studio      Michael Karas      02/13/12 09:55      
         LP ISP Studio      Jan Waclawek      02/13/12 11:12      
   Reset?      Per Westermark      02/13/12 01:15      
      hitting the nail on the head?      Erik Malund      02/13/12 07:10      
         'LP5x accepts both polarities of reset      Jan Waclawek      02/13/12 07:47      
            How?      Per Westermark      02/13/12 07:55      
               Care to read the fine manual, Per? :-)      Jan Waclawek      02/13/12 07:59      
                  don't know about Per, I would not ....      Erik Malund      02/13/12 09:10      
                  Information can sometimes be hidden      Per Westermark      02/13/12 09:13      
               Here is How!!      Michael Karas      02/13/12 09:01      
   Program      JecksonS Ben      02/13/12 01:58      
      UART-ISP? I doubt it.      Jan Waclawek      02/13/12 05:24      
         Uart-SPI      JecksonS Ben      02/14/12 03:34      
            UART bootloader      Jan Waclawek      02/14/12 12:46      
               UART bootloader      Erik Malund      02/14/12 13:13      
               already inside      JecksonS Ben      02/15/12 03:10      
                  IAP don't mean boot loader exists      Per Westermark      02/15/12 04:47      
                     IAP for flash      JecksonS Ben      02/16/12 01:21      
                  two mistakes      Erik Malund      02/15/12 10:12      
                     ISP sometimes supported with zero boot loader      Per Westermark      02/15/12 10:24      
               Atmel..      JecksonS Ben      02/16/12 01:49      
   89LP52      Rick Gebhardt      02/13/12 18:21      
      Thanks for the reply!      Andy Neil      02/14/12 00:46      
      OH, NO        Erik Malund      02/14/12 07:42      
         FLIP is Atmel's PC-side utility for UART bootloaders      Jan Waclawek      02/14/12 12:57      
            FLIP      JecksonS Ben      02/16/12 01:15      
   STK500 RS232 link commands      Jim Granville      02/15/12 22:13      
      yet another choice..      Jim Granville      02/16/12 16:31      
      AT89LP52      Rick Gebhardt      02/21/12 01:35      
      AT89LP52      Rick Gebhardt      02/21/12 01:42      
         Programmers for AT89S and AT89LP        KONSTANTINOS L. ANGELIS      02/21/12 02:16      
            AT89LP52      Rick Gebhardt      02/21/12 23:15      
               AT89ISP      Jim Granville      02/22/12 00:12      
                  I'd be wary      Erik Malund      02/22/12 09:55      
                     way      JecksonS Ben      02/24/12 01:07      
            The very very low cost solution      JecksonS Ben      02/22/12 01:24      
         AT89LP52 options      Jim Granville      02/21/12 02:27      

Back to Subject List