Email: Password: Remember Me | Create Account (Free)

Back to Subject List

Old thread has been locked -- no new posts accepted in this thread
Jecksons Ben
02/22/12 01:24
Read: 861 times
Makassar
Indonesia


 
#186130 - The very very low cost solution
Responding to: Konstantinos L. Angelis's previous message
For a hobby project this is easy enough
http://www.lancos.com/prog.html


Yes..This is the cheap but more this this...

Once the 89LP52/51 programmed..We agree that IAP able to work.Cause IAP "bootloader" didn't shipped with new chip,but after 1st programmed then IAP "bootloader" works and TX/RX could modified entire FLASH with expert programmer via Hyperterminal/Bray/Putty.

Program all the brand new chips with "trash Flash code" then Play with IAP(expert way with TX/RX).

Thank you
Jeckson S Ben



List of 42 messages in thread
TopicAuthorDate
89LP52      Rick Gebhardt      02/12/12 23:58      
   Drop In Replacement??      Michael Karas      02/13/12 00:15      
   Always give full part numbers!      Andy Neil      02/13/12 00:52      
      STK500, AVRStudio et al.      Jan Waclawek      02/13/12 01:55      
         Officially recommended      Per Westermark      02/13/12 02:51      
      AT89LP Developer Studio      Michael Karas      02/13/12 09:55      
         LP ISP Studio      Jan Waclawek      02/13/12 11:12      
   Reset?      Per Westermark      02/13/12 01:15      
      hitting the nail on the head?      Erik Malund      02/13/12 07:10      
         'LP5x accepts both polarities of reset      Jan Waclawek      02/13/12 07:47      
            How?      Per Westermark      02/13/12 07:55      
               Care to read the fine manual, Per? :-)      Jan Waclawek      02/13/12 07:59      
                  don't know about Per, I would not ....      Erik Malund      02/13/12 09:10      
                  Information can sometimes be hidden      Per Westermark      02/13/12 09:13      
               Here is How!!      Michael Karas      02/13/12 09:01      
   Program      JecksonS Ben      02/13/12 01:58      
      UART-ISP? I doubt it.      Jan Waclawek      02/13/12 05:24      
         Uart-SPI      JecksonS Ben      02/14/12 03:34      
            UART bootloader      Jan Waclawek      02/14/12 12:46      
               UART bootloader      Erik Malund      02/14/12 13:13      
               already inside      JecksonS Ben      02/15/12 03:10      
                  IAP don't mean boot loader exists      Per Westermark      02/15/12 04:47      
                     IAP for flash      JecksonS Ben      02/16/12 01:21      
                  two mistakes      Erik Malund      02/15/12 10:12      
                     ISP sometimes supported with zero boot loader      Per Westermark      02/15/12 10:24      
               Atmel..      JecksonS Ben      02/16/12 01:49      
   89LP52      Rick Gebhardt      02/13/12 18:21      
      Thanks for the reply!      Andy Neil      02/14/12 00:46      
      OH, NO        Erik Malund      02/14/12 07:42      
         FLIP is Atmel's PC-side utility for UART bootloaders      Jan Waclawek      02/14/12 12:57      
            FLIP      JecksonS Ben      02/16/12 01:15      
   STK500 RS232 link commands      Jim Granville      02/15/12 22:13      
      yet another choice..      Jim Granville      02/16/12 16:31      
      AT89LP52      Rick Gebhardt      02/21/12 01:35      
      AT89LP52      Rick Gebhardt      02/21/12 01:42      
         Programmers for AT89S and AT89LP        KONSTANTINOS L. ANGELIS      02/21/12 02:16      
            AT89LP52      Rick Gebhardt      02/21/12 23:15      
               AT89ISP      Jim Granville      02/22/12 00:12      
                  I'd be wary      Erik Malund      02/22/12 09:55      
                     way      JecksonS Ben      02/24/12 01:07      
            The very very low cost solution      JecksonS Ben      02/22/12 01:24      
         AT89LP52 options      Jim Granville      02/21/12 02:27      

Back to Subject List