Email: Password: Remember Me | Create Account (Free)

Back to Subject List

Old thread has been locked -- no new posts accepted in this thread
Per Westermark
03/09/12 02:14
Read: 536 times
Sweden


 
#186517 - People responding to specific questions
Responding to: ???'s previous message
Have you added a DC component - or do you have an ADC that can measure negative values?

If all you see is the positive half-cycle, then it depends on how well you did your previous steps if you have introduced a DC error somewhere. But it will be interesting to detect the zero crossing if your ADC don't see samples on both sides of that zero-crossing.

Another thing - you have a step where you attenuate to 0.5V? Or attenuate to 5-0.5 = 4.5V?

Third thing - how can you calibrate your device? On scale and offset errors?

Fourth thing - if your ADC has a reasonably fast conversion rate, you can convert and pick up values in an interrupt routine while leaving the rest of the time for the main program.

Sorry but people don't just get excited about someones measurement issues unless you post specific questions. We don't want to write complete programs for other people when we can instead make money by writing complete programs for customers.

Do you have any specific questions?

For now, you haven't even clearly indicated exactly what kind of wave the ADC would be able to pick up.

Note that the top value of a sine wave has quality issues if there is noise in the measurements.
Next thing is if you want true RMS or just guestimate RMS based on the peak voltage. For true RMS, you need to measure the energy, i.e. sample for the full cycle of the sine wave.

List of 66 messages in thread
TopicAuthorDate
Sine wave detection on microcontroller      Yagnesh Mehta      03/07/12 04:59      
   Detect or measure?      Per Westermark      03/07/12 05:25      
      not detection, measurement of sine wave signal      Yagnesh Mehta      03/07/12 06:14      
         What are you measuring?      Andy Peters      03/07/12 10:05      
            RMS and Average - 1st Priority      Yagnesh Mehta      03/07/12 20:59      
               415 v      Mahmood Elnasser      03/08/12 22:07      
                  I have to do using MCU      Yagnesh Mehta      03/08/12 22:48      
                     Start simple      Mahmood Elnasser      03/08/12 23:17      
                        if time is major isssue than.....      Yagnesh Mehta      03/08/12 23:31      
                           People responding to specific questions      Per Westermark      03/09/12 02:14      
                              Same Technique....      Yagnesh Mehta      03/09/12 04:32      
                                 RMS      Maarten Brock      03/09/12 05:49      
                                    Sorry for my laziness        Yagnesh Mehta      03/09/12 20:50      
                                 So what have you done?      Per Westermark      03/09/12 06:19      
                                    Require more work...      Yagnesh Mehta      03/10/12 00:50      
                                    Working on that      Yagnesh Mehta      03/10/12 06:12      
                                       options, options      Per Westermark      03/10/12 06:49      
   Help me      Yagnesh Mehta      03/08/12 21:31      
      Okay      Joseph Hebert      03/09/12 06:13      
         Are many threads available      Per Westermark      03/09/12 06:29      
      when you save a char ...        Erik Malund      03/09/12 08:09      
      Why don't you specify your problem COMPLETELY?      Richard Erlacher      03/09/12 11:36      
         Already specify it      Yagnesh Mehta      03/10/12 02:07      
            there are some details?      Richard Erlacher      03/10/12 07:51      
               comparisions      Yagnesh Mehta      03/12/12 01:16      
                  How are you calculating your needed sample rate?      Per Westermark      03/12/12 01:54      
                     start with simple one....      Yagnesh Mehta      03/12/12 08:02      
                        You do know sin(90+angle)? Or 2-log computations?      Per Westermark      03/12/12 08:48      
                           ADC resolution............      Yagnesh Mehta      03/12/12 12:27      
                              impossible or wrong      Erik Malund      03/12/12 13:30      
                              double post, ignore      Erik Malund      03/12/12 13:30      
                  Precision Rectify:      Erik Malund      03/12/12 06:44      
                     SCR Chopped Wave      Yagnesh Mehta      03/12/12 07:48      
                        What accuracy do you need?      Kalpak Dabir      03/12/12 08:43      
                           CT accuracy      Yagnesh Mehta      03/12/12 12:58      
                              the fundamental      Erik Malund      03/12/12 13:41      
                              50Hz      Per Westermark      03/12/12 14:27      
                              Precision rectifier is suitable for any waveform      Kalpak Dabir      03/13/12 01:47      
                                 are u sure??      Yagnesh Mehta      03/13/12 08:03      
                                    Depends      Per Westermark      03/13/12 09:08      
                                    must be severely bandwidth limited      Erik Malund      03/13/12 09:11      
                                       Maybe was circuit with top-voltage capacitor      Per Westermark      03/13/12 09:17      
                                       Sorry for confusion      Yagnesh Mehta      03/14/12 00:18      
                                          What accuracy do you need?      Kalpak Dabir      03/14/12 01:23      
                                             360/1024      Yagnesh Mehta      03/14/12 01:41      
                                                Not what he (or me) have asked      Per Westermark      03/14/12 04:39      
                                                   you are right....      Yagnesh Mehta      03/14/12 11:51      
                                                Do you believe you can protect your circuit from noise?      Richard Erlacher      03/14/12 08:19      
                                                   Very Noisy environment      Yagnesh Mehta      03/14/12 11:57      
                                                      re Very Noisy environment      Erik Malund      03/14/12 12:23      
                                                         Some of those rules are showing their age      Richard Erlacher      03/14/12 20:00      
                                                            here we go again      Erik Malund      03/15/12 08:15      
                                                               think about this for a minute      Richard Erlacher      03/15/12 17:10      
                                                                  when discussing a FAQ      Erik Malund      03/16/12 06:49      
                                                                     Well, when were those cap sizes determined?      Richard Erlacher      03/16/12 09:53      
                                                                        Technology      Per Westermark      03/16/12 10:13      
                                                                           Steady state currents do not need decaps      Kalpak Dabir      03/16/12 22:48      
                                                                              Often low capacitance so limited charge. But remember load.      Per Westermark      03/17/12 06:41      
                                                                        fixations      Erik Malund      03/16/12 10:40      
                                                                           Nothing. has been proven yet.      Richard Erlacher      03/18/12 13:15      
                                                                              once more for the peanut gallery      Erik Malund      03/19/12 07:23      
                                                                                 Where you sit determines what you see ...      Richard Erlacher      03/20/12 01:56      
                                                                                    Off-topic        Per Westermark      03/20/12 02:01      
                                                                                       difficult when ...      Erik Malund      03/20/12 06:59      
                                                                                       Yes ... I don't know how we got here either      Richard Erlacher      03/20/12 09:32      
                                                                                          i do      Erik Malund      03/20/12 09:45      

Back to Subject List