Email: Password: Remember Me | Create Account (Free)

Back to Subject List

Old thread has been locked -- no new posts accepted in this thread
Jim Granville
04/01/12 14:54
Read: 805 times


 
#186968 - Test standard solutions
Responding to: Andy Neil's previous message
Andy Neil said:

What if you use an off-the-shelf FTDI cable?
That would show whether it's an inherent FTDI issue, or an issue with your particular implementation...


Certainly a good idea, and try more than one FTDI option - eg their new FT(2)232H series has larger buffers, and finer baud options, and their new X series should include 'field experience' revisions.

The fault descriptions here seem to be vague, and sometimes conflicting.

There could be more than one failure mode, and any failure that has data-content dependence, is not likely to be physical.
Send test patterns, that progressively get more baud-rigorous, and even do a Baud-scan, and plot the results.

List of 36 messages in thread
TopicAuthorDate
FTDI F232RL Noise issues      Raj Nambiar      03/31/12 08:42      
   GND,cables      Stefan KAnev      03/31/12 11:51      
      of this is it, then      Erik Malund      03/31/12 14:19      
   leakage effects..      Jim Granville      03/31/12 16:46      
      Thanks for the comments..      Raj Nambiar      04/01/12 02:02      
         changing the serial port data....      Stefan KAnev      04/01/12 05:11      
         cable, bought off the shelf      Andy Neil      04/01/12 09:00      
            Test standard solutions      Jim Granville      04/01/12 14:54      
               Options..      Raj Nambiar      04/01/12 23:44      
                  VCP /D2X      Stefan KAnev      04/02/12 03:37      
                     Problem exists with both drivers      Raj Nambiar      04/02/12 08:34      
                  Aten serial to USB cable uses a FTDI chip      Kalpak Dabir      04/02/12 04:16      
   FTDI chip ESD sensitivity        Oliver Sedlacek      04/02/12 06:13      
      Thanks Oliver...      Raj Nambiar      04/02/12 08:30      
         Zeners are slow      Erik Malund      04/02/12 08:59      
         show Your circuit      Stefan KAnev      04/02/12 11:04      
            F232 is USB powered but.. + circuit      Raj Nambiar      04/03/12 01:32      
         USB Isolator Chips      Neil Kurzman      04/02/12 21:50      
            Isolators      Raj Nambiar      04/03/12 02:00      
         Better than zeners      Oliver Sedlacek      04/03/12 07:30      
            just a thought      Erik Malund      04/03/12 07:45      
               Layout      Raj Nambiar      04/03/12 22:13      
                  VCP/Direct drivers      Raj Nambiar      04/03/12 23:49      
                  Layout attached      Raj Nambiar      04/04/12 00:51      
                     It's a high speed circuit !!!!      Oliver Sedlacek      04/04/12 05:09      
                        Totally 100% Agreed      Michael Karas      04/04/12 05:34      
                           the trouble with schematics ....      Erik Malund      04/04/12 07:36      
                              Bandwidth limitation      Per Westermark      04/04/12 09:08      
   22 ohms between serial port ground and FT232 ground helps...      Raj Nambiar      04/05/12 23:58      
      of course it does      Erik Malund      04/06/12 08:01      
         Erik,      Raj Nambiar      04/06/12 09:45      
            Links please      Bert Van Den Berg      04/13/12 13:44      
               Link...      Raj Nambiar      04/16/12 00:12      
                  Solved      Raj Nambiar      06/15/12 23:59      
                     Magnetics      Per Westermark      06/16/12 02:08      
                        Ethernet input is connected to serial port ground      Raj Nambiar      06/22/12 08:56      

Back to Subject List