Email: Password: Remember Me | Create Account (Free)

Back to Subject List

Old thread has been locked -- no new posts accepted in this thread
Raj Nambiar
04/03/12 22:13
Read: 892 times
Dubai
Uae


 
#186997 - Layout
Responding to: Erik Malund's previous message
layout, is not so good. The length of data lines aren't exactly same, and they may not be exactly parallel.

Data rate is low. 50 bytes in 2 seconds. 2400 serial port baud.

Tried shortest decoupling on the chip, across the width.

FTDI guys have taken the layout and circuit, and I am waiting for a reply. Is there a possibility that the FTDI chip is not designed for such applications? That it should be used in less demanding situations ?

List of 36 messages in thread
TopicAuthorDate
FTDI F232RL Noise issues      Raj Nambiar      03/31/12 08:42      
   GND,cables      Stefan KAnev      03/31/12 11:51      
      of this is it, then      Erik Malund      03/31/12 14:19      
   leakage effects..      Jim Granville      03/31/12 16:46      
      Thanks for the comments..      Raj Nambiar      04/01/12 02:02      
         changing the serial port data....      Stefan KAnev      04/01/12 05:11      
         cable, bought off the shelf      Andy Neil      04/01/12 09:00      
            Test standard solutions      Jim Granville      04/01/12 14:54      
               Options..      Raj Nambiar      04/01/12 23:44      
                  VCP /D2X      Stefan KAnev      04/02/12 03:37      
                     Problem exists with both drivers      Raj Nambiar      04/02/12 08:34      
                  Aten serial to USB cable uses a FTDI chip      Kalpak Dabir      04/02/12 04:16      
   FTDI chip ESD sensitivity        Oliver Sedlacek      04/02/12 06:13      
      Thanks Oliver...      Raj Nambiar      04/02/12 08:30      
         Zeners are slow      Erik Malund      04/02/12 08:59      
         show Your circuit      Stefan KAnev      04/02/12 11:04      
            F232 is USB powered but.. + circuit      Raj Nambiar      04/03/12 01:32      
         USB Isolator Chips      Neil Kurzman      04/02/12 21:50      
            Isolators      Raj Nambiar      04/03/12 02:00      
         Better than zeners      Oliver Sedlacek      04/03/12 07:30      
            just a thought      Erik Malund      04/03/12 07:45      
               Layout      Raj Nambiar      04/03/12 22:13      
                  VCP/Direct drivers      Raj Nambiar      04/03/12 23:49      
                  Layout attached      Raj Nambiar      04/04/12 00:51      
                     It's a high speed circuit !!!!      Oliver Sedlacek      04/04/12 05:09      
                        Totally 100% Agreed      Michael Karas      04/04/12 05:34      
                           the trouble with schematics ....      Erik Malund      04/04/12 07:36      
                              Bandwidth limitation      Per Westermark      04/04/12 09:08      
   22 ohms between serial port ground and FT232 ground helps...      Raj Nambiar      04/05/12 23:58      
      of course it does      Erik Malund      04/06/12 08:01      
         Erik,      Raj Nambiar      04/06/12 09:45      
            Links please      Bert Van Den Berg      04/13/12 13:44      
               Link...      Raj Nambiar      04/16/12 00:12      
                  Solved      Raj Nambiar      06/15/12 23:59      
                     Magnetics      Per Westermark      06/16/12 02:08      
                        Ethernet input is connected to serial port ground      Raj Nambiar      06/22/12 08:56      

Back to Subject List